Commercial · Tampa, FL
Since 2015, Titan Mobile Welding Tampa has handled tank welding repair for leaking, cracked, and corroded tanks that cannot wait for shop downtime. We bring mobile TIG, MIG, and stick welding to your site in Tampa to restore safe service and extend tank life.
Every tank repair starts with identification and prep so the weld is sound, not just sealed. We verify tank material (carbon steel, stainless steel, aluminum), wall thickness, and joint type, then isolate and depressurize where applicable. Surfaces get cleaned to bright metal by grinding and wire-brushing, coatings are removed back beyond the heat-affected zone, and cracks are stop-drilled when needed. For thin wall tanks, we control heat input, fit patches and backing where appropriate, and choose filler metal to match base metal and service conditions.
Florida heat, humidity, and salt air accelerate corrosion and make coating work just as important as welding. After welding, we blend and inspect the repair area, then prep for protective finishes such as epoxy primer, industrial enamel, or compatible corrosion-inhibitive coatings when requested. For outdoor tanks and equipment, we can add reinforcement plates, gussets, or saddles to reduce flexing and future cracking, and we can repair or replace brackets, lifting lugs, and mounting tabs. If the tank is used for water, fuel, or process fluids, we plan the repair around cleanliness and safe re-commissioning so you are not chasing contamination or repeat leaks.
Tampa customers choose us because we show up ready to diagnose the cause, not just burn in a bead. Our mobile rigs support TIG (GTAW) for clean stainless and aluminum work, MIG (GMAW) for controlled production repairs, and stick (SMAW) for heavy steel and outdoor conditions. You get practical recommendations on whether to weld, patch, reinforce, or replace, with a free written estimate and clear scope. As a licensed and insured mobile welding contractor, we prioritize safe isolation, fire prevention, and site protection so your facility or property stays controlled during hot work.
Before we leave, we walk the repair with you and confirm fit, alignment, and finish so the tank is ready for service. You receive a written estimate up front, documentation of the repair location and method upon request, and straightforward guidance on cure times for coatings and when to return the tank to use. If access is tight, we plan around manways, baffles, and surrounding equipment to minimize disassembly and downtime. Schedule tank welding repair when you need a dependable field fix that holds, with workmanship aimed at long-term reliability.
Yes. We provide a free written estimate with scope, materials, and labor after reviewing photos and/or an on-site evaluation.
In most cases, no. Our mobile setup is designed to weld on-site for gates, railings, trailers, frames, brackets, and equipment so you avoid transport and downtime.
Yes. We perform aluminum and stainless work when the project calls for it, commonly using TIG (GTAW) for controlled heat and clean results.
Yes, depending on the application and access. We evaluate base metal condition, joint design, and loading, then recommend a repair or replacement approach that is safe and appropriate.
We can prep and apply rust-inhibitive primer and paint-ready finishing on many jobs. Final coating options depend on the environment, desired finish, and existing coating system.
Tank failures rarely start as a sudden blowout. Most begin as pinhole leaks, cracked weld seams, corrosion around fittings, or fatigue at mounts and saddles. Titan Mobile Welding Tampa provides mobile tank welding repair for steel, stainless, and aluminum tanks, bringing the right process and prep to your location so you can restore service without hauling large equipment to a shop.
We focus on repairs that last by addressing the root cause. That means removing coatings back beyond the weld zone, cleaning to bright metal, and correcting poor fit-up, thin edges, or contamination that can cause porosity. Depending on the tank and service, we may use TIG (GTAW) for precise control on thinner sections and stainless, MIG (GMAW) for consistent fusion on shop-like work in the field, or stick (SMAW) for heavier steel and wind-exposed conditions. Common repairs include seam cracks, rust-through, damaged nozzles and couplings, leaking drain ports, and failed brackets or supports.
Environmental exposure matters in Tampa. High humidity and coastal air can accelerate rust at weld toes and around dissimilar metals, so we can coordinate surface prep and compatible coatings after welding to slow corrosion. When movement or vibration is the culprit, reinforcement plates, gussets, and improved mounting can reduce stress and help prevent repeat failures. We also plan safe access around manways, piping, and nearby equipment to keep disruption low.
If you need tank welding repair, send photos and basic details (material, thickness if known, what the tank holds, and whether it is in service). We will provide a free written estimate, explain the repair approach, and schedule mobile service with clear safety requirements for isolation and hot work. Call Titan Mobile Welding Tampa to get the leak handled and the tank back in service.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Tampa. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
